Sbs Bitumen Waterproof Roofing Membrane

SBS bitumen waterproof roofing membrane is SBS (styrene - butadiene - styrene)thermoplastic elastomer modified bitumen as dip coating materials to high-quality polyester felt, fiberglass mat, cloth compound tires for the tire base to fine sand, mineral(film), PE film, aluminum and other materials for the cladding, using special mechanical mixing and grinding of elastomer modified bitumen membrane.


Specification
SBS bitumen waterproof roofing membrane

Surface materials:
PE film, aluminum foil, fine sand, mineral(film) etc. 


Product features
* Good performance in good impermeability.
* Possess good tensile strength, elongation rate and size stability which could be well suited the substrate distortion and crack.
* Low temperature resistance, it still works at -50ºC, especially suitable for cold areas.
* Anti-puncture, Tear-resistance.
* Anti-broker, anti-resistance, anti-erosion, anti-mildew, anti-weathering.
* Easy to apply.



Application range
1, Roof, wall, basement, toilet Of industrial and civil buildings.
2, Road, bridge, parking lot, swimming pool and impounding reservoir etc.
3, Especially suitable for the building who's structure change continually and the construction of cold areas.

Application method
There are two methods in application:
a) One way is by heating and melting method. Heat the polyethylene film of the membrane and roof deck surface by heating and melting method to be nearly melted (not flowing), then install the membrane filly bonded to the roof deck with overlaps of 5-10cm.
b) The other way is by cold adhesive method.Pour the cold adhesive homogeneously on the roof deck, then roll the membrane to install it to be fully sticked to roof deck.
By heating and melting method and by cold adhesive can be used in alternation in application as requested. After application, a full serious inspection is required to sure no air bubble, no falling away. etc. to guarantee the waterproof life.



Storage and transport:

Avoid exposure to sun and rain and store in dry and ventilated environment. Storage temperature should not be lower than of the corresponding product compliance test, should not be higher than 50 ºC. Vertical storage, height not more than two layers.Transportation must stand, no more than two layers, to prevent inclined or horizontal pressureUnder normal storage and transport conditions, the storage period is one year from the date of production.The process of transportation and storage should be far from the fire source

Technology Data


Details of construction

The special formulation of fire enables the membrane to be applied directly with primer. This application is named as "Torched on application".   
1. Base processing: the base surface musts be clean,solid,level,dry;no grit,rift and loosing dust. For a large recess, fill it with cement mortar and then level it. Remove the protrusion and clean dust If working on base slab or lateral face,water lowering should be done.
2. Painting primer before laying the membrane, clean the dust on the surface of concrete base with dust catcher or dust-blower; then paint entirely with treatment agent of DY primer for waterproofing(for purpose of dust consolidation and high adhesive effect).
3. Heat to melt: place membrane correctly, fire torch, heat the membrane with base entirely, when the surface of the membrane is black and bright with a fusion layer, apply the membrane and press it into a solid and flat state. Before the membrane is cool, seal the edge of joint by float.
4. Requirements for lapping: There should be less than 3 layers of lapping, with the joint seams appearing as"T" type, avoid 4 layers of lapping. The width of longitudinal lapping is between 50 and 80mm, and of end-lap joint 100mm
5. Use a roller to push hard the membrane surface to ensure it stick firmly.
 

The base should be dry and clean. Do not work in the rainy or snowy day.
2. Do not work under heavy wind(above 5 grade).
3. Unsuitable for construction below 5°C.
4. If it is rain or snow in the process of construction, protective measure to the laid membrane is must.
5. All the workers should put on special uniforms to keep safe when installing. There should be equipments for fire controls.